speed dating wausau wi - Updating ios via xmodem

You can check out the required procedure by clicking HERE!

Once you’ve booted your switch into Switch ROM mode you’ll be see the following dispatch; Boot Sector Filesystem (bs) installed, fsid: 2 Base ethernet MAC Address: :f2:d Xmodem file system is available. The system has been interrupted prior to initializing the flash filesystem. 100% 12181 KB 6 KB/s 0 Errors ................................................................. File "xmodem:" successfully copied to "flash:c3560-ipservicesk9-mz.122-53. SE.bin" switch: Loading "flash:/c3560-ipservicesk9-mz.122-53. SE.bin"[email protected]@@@@@@@@@@@@@@@@@ @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ File "flash:/c3560-ipservicesk9-mz.122-53.

The following commands will initialize the flash filesystem, and finish loading the operating system software: flash_init boot switch: Initializing Flash... ................................................................. ................................................................. ................................................................. ................................................................. ................................................................. ................................................................. ................................................................. ................................................................. ................................................................. ................................................................. ................................................................. ................................................................. ................................................................. SE.bin" uncompressed and installed, entry point: 0x1000000 executing...

flashfs[0]: 1 files, 1 directories flashfs[0]: 0 orphaned files, 0 orphaned directories flashfs[0]: Total bytes: 15998976 flashfs[0]: Bytes used: 12474880 flashfs[0]: Bytes available: 3524096 flashfs[0]: flashfs fsck took 10 seconds. switch: Are you sure you want to format "flash:" (all data will be lost) (y/n)? Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 170 West Tasman Drive San Jose, California 95134-1706 Cisco IOS Software, C3560 Software (C3560-IPSERVICESK9-M), Version 12.2(53)SE, RELEASE SOFTWARE (fc2) Technical Support: Copyright (c) 1986-2009 by Cisco Systems, Inc. laws governing Cisco cryptographic products may be found at: you require further assistance please contact us by sending email to [email protected] cisco WS-C3560-24PS (Power PC405) processor (revision M0) with 131072K bytes of memory.

XMODEM is an alternative method of upload that is much slower, and involves sending the file over the serial port, but doesn't require a TFTP server, or the network to be working to proceed with.

Even if you plan on using TFTP, I suggest familiarizing yourself with the XMODEM upload procedure as a just-in-case measure for future reference.

Updating the IOS on a Cisco 2960 is a straightforward procedure when connected to the Cisco 2960 command line interface (CLI) using a serial console cable.

Things You’ll Need Instructions to Upgrade a Cisco 2960 IOS With a Console Cable 1. Enter a name for the connection in the “Name:” field presented in the Hyperterminal window that appears, and then tap the “Enter” key.

For this I will be using tftp as we can upload the whole package including the useless web page. The last current IOS according to Cisco at the time of writing this was 12.0-5 WC17.

If the flash has been deleted / formatted and there is no IOS on the switch or router, you have to copy the new IOS via the console port.

I usually call that something like C:\TFTP-Root or C:\TFTPBoot If you want a redhat box to be your tftp server, instead of Windows, just (on the redhat box) yum install tftp-server Change disable=yes to disable=no in /etc/xinetd.d/tftp /etc/init.d/xinetdrestart And drop the file in /tftpboot Assign a management IP address to your switch as described by Pete Long.

Tags: , ,